Product code: KCV011
These are installed between the channel and the substrate to allow free flow of water to drain out of the system...
€3.93 Ex. VAT
Product code: KCV010
These are installed between the channel and the substrate to allow free flow of water to drain out of the system.
W = 72mm H = 10mm L = 90mm..
€3.93 Ex. VAT
Product code: KCV035
Additional gasket can be supplied in any length.
This gasket suits 12mm to 17.5mm thick glass.
Small gasket is also available for 19mm to 21.5mm...
€3.47 Ex. VAT
Product code: KCV037
Balcony Seal® is a revolutionary product that provides a solution to both water drainage and waterproofing on a balcony installation. It comprises of drain blocks that sit underneath the balustrade channel. Notches on the top side of the drain blocks locate into the rebates of the Crystal View chann..
€99.08 Ex. VAT
Product code: KCV006
Stainless steel end caps cut to suit the surface mounted channel.
An adhesive will be needed to hold the end cap in place...
€10.92 Ex. VAT
Product code: K.ON.90.7001.440.31
Suitable for use with the 6500 & 6501 profiles
4mm in diameter and 40mm long connecting pins for the easy alignment and installation of the main profile.
Supplied in packs of 8
2 required per joint...
€10.95 Ex. VAT
Product code: KCV006A
Stainless steel end caps cut to suit the surface mounted channel.
For use where no base cladding has been used.
Easily mounted to the end of the channel without the need for adhesives as it has two dowels for easy alignment and attachment...
€23.63 Ex. VAT
Product code: KCV036
Additional gasket can be supplied in any length.
This gasket suits 19mm to 21.5mm thick glass.
Large gasket is also available for 12mm to 17.5mm...
€3.47 Ex. VAT
Product code: KCV008
Specially designed 10mm spanner used for tightening and adjusting the glass in the channel...
€9.26 Ex. VAT
Product code: K.ON.90.0502.010.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 10mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side only..
€52.10 Ex. VAT
Product code: KCV009
These dowels are used for joining two channels and ensure a strong and accurate joint.
Sold separately.
Two dowels needed per joint.
These can be used with both the Crystal View and Mega Grip systems...
€1.59 Ex. VAT
Product code: K.ON.90.0502.011.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 10.76mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side o..
€52.10 Ex. VAT
Product code: K.ON.90.0502.012.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 12mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side only..
€52.10 Ex. VAT
Product code: B0012
VistaLevel enables the quick horizontal positioning of glass panes. Fasten the little helper in a way that you can keep an eye on it during installation.
The proven vacuum technology of the VistaLevel® suction pad holds it safely in place. Now you have both hands free to comfortably align the ..
€54.18 Ex. VAT
Product code: K.ON.90.0502.013.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 12.76mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side o..
€52.10 Ex. VAT
Product code: K.ON.90.0502.017.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 16.76mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side o..
€52.10 Ex. VAT
Product code: K.ON.90.0502.018.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 17.52mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side o..
€52.10 Ex. VAT
Product code: K.ON.90.0502.112.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 12mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side only..
€63.18 Ex. VAT
Product code: K.ON.90.0502.115.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 15mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side only..
€63.18 Ex. VAT
Product code: K.ON.90.0502.118.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 17.52mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side o..
€63.18 Ex. VAT
Product code: K.ON.90.0502.119.00
Installation kit suitable for 2.5metres of channel and a glass thickness of 19mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
The flex fit system allows for installation and plumbing of the glass from one side only..
€63.18 Ex. VAT
Product code: K.ON.90.0502.322.00
Suitable for use with the 3kN Systems and 1.5kN 3031 Side System.
For use with a glass thickness of 21.52mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
It allows for installation and plumbing of the glass from ..
€72.18 Ex. VAT
Product code: K.ON.90.0502.326.00
Suitable for use with the 3kN Systems and 1.5kN 3031 Side System.
For use with a glass thickness of 25.52mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
It allows for installation and plumbing of the glass from ..
€72.18 Ex. VAT
Product code: K.ON.90.0502.332.00
Suitable for use with the 3kN Systems and 1.5kN 3031 Side System.
For use with a glass thickness of 31.52mm.
The flex fit system allows for the plumbing of each individual glass panel up to 34mm in relation to the perpendicular.
It allows for installation and plumbing of the glass from ..
€72.18 Ex. VAT
Product code: K.ON.90.7001.640.31
40mm long connecting pins for the easy alignment and installation of the main profile.
2 required per joint...
€12.10 Ex. VAT
Product code: K.ON.90.0100.110.00
The Flex Fit tool allows you to easily fit the flex fit clamps to the profile.
This tool allows you to adjust/plumb the glass easily from one side without marking or damaging the main profile...
€33.99 Ex. VAT
Product code: K.ON.90.0100.100.00
The combi tool is generally used for installing the fixed wedges once the glass is plumbed.
It it is also used to smoothly install the rubber gaskets without the need to continually bend down making the installation faster and neater...
€147.96 Ex. VAT
Product code: K.ON.90.7012.012.10
This is a must have installation item for any installer.
This is a stepped wedge/shim that starts at 1mm and goes in steps up to 6.5mm thick.
Ideal for plumbing frameless balustrade tracks before glass installation to enable easier and faster glass installation and plumbing especially on single si..
€34.46 Ex. VAT
Product code: KCV007L
Stainless steel end caps cut to suit the side mounted channel when used with the bottom cladding.
An adhesive will need to be used to hold them in place.
Due to the design, these are available in right and left hand models...
€13.65 Ex. VAT
Product code: KCV007R
Stainless steel end caps cut to suit the side mounted channel when used with the bottom cladding.
An adhesive will need to be used to hold them in place.
Due to the design, these are available in right and left hand models...
€13.65 Ex. VAT
Showing 1 to 31 of 31 (1 Pages)